Transverse viscoelastic properties of pulp fibers investigated with an atomic force microscopy method

Caterina Marina Czibula, Christian Ganser, Tristan Seidlhofer, Christian Teichert , Ulrich Hirn

Research output: Contribution to specialist publicationArticleResearchpeer-review

Abstract

Changes in moisture content of single pulp fibers have an immense influence on the behavior of paper and paper products. Here, an atomic force microscopy (AFM)-based method is applied to investigate the viscoelastic properties of pulp fibers at varying relative humidity (RH) in the transverse direction. Pulp fibers have not only anisotropic properties, but also a very rough surface due to their hierarchical structure. For this reason, we have developed a specific load schedule for the AFM-based test method to overcome uncertainties and limitations due to surface roughness of the pulp fibers. The evaluation of the experimental data combines contact mechanics and viscoelastic models which consist of springs and dashpots in series or parallel describing elastic and viscous behavior. Here, it will be demonstrated that the so-called Generalized Maxwell (GM) model yields comparable results for single pulp fibers at five different RH values and in water. The moisture changes lead to a decrease in the elastic modulus but increase in the relaxation effects with increasing RH. All the determined parameters for the elastic and viscous behavior exhibit a gradual decrease with increasing RH from 10 to 75% RH. The elastic moduli decrease by a factor of 10 and the viscosities are decreasing by a factor of 10–20. In water, there is an even more pronounced decrease of the elastic moduli by a factor 100, and the viscosities decrease by at least three orders of magnitude compared to 10% RH. This indicates that the mechanical response of pulp fibers in water is significantly different than in humid air. This is also illustrated by the fact that a GM model of order two suffices to describe the material behavior in humid air but a GM model of order three is necessary to fit the material behavior in water. A possible interpretation is an additional relaxation effect of the pulp fiber wall in water.

LanguageEnglish
Specialist publicationJournal of Materials Science
DOIs
StatusPublished - 2019

Fingerprint

Pulp
Atomic force microscopy
Atmospheric humidity
Fibers
Water
Elastic moduli
Moisture
Viscosity
Paper products
Air
Mechanics
Surface roughness

ASJC Scopus subject areas

  • Mechanics of Materials
  • Mechanical Engineering
  • Materials Science(all)

Cite this

Transverse viscoelastic properties of pulp fibers investigated with an atomic force microscopy method. / Czibula, Caterina Marina; Ganser, Christian; Seidlhofer, Tristan; Teichert , Christian; Hirn, Ulrich.

In: Journal of Materials Science, 2019.

Research output: Contribution to specialist publicationArticleResearchpeer-review

@misc{25c2315291d6452c952bba1557d842a3,
title = "Transverse viscoelastic properties of pulp fibers investigated with an atomic force microscopy method",
abstract = "Changes in moisture content of single pulp fibers have an immense influence on the behavior of paper and paper products. Here, an atomic force microscopy (AFM)-based method is applied to investigate the viscoelastic properties of pulp fibers at varying relative humidity (RH) in the transverse direction. Pulp fibers have not only anisotropic properties, but also a very rough surface due to their hierarchical structure. For this reason, we have developed a specific load schedule for the AFM-based test method to overcome uncertainties and limitations due to surface roughness of the pulp fibers. The evaluation of the experimental data combines contact mechanics and viscoelastic models which consist of springs and dashpots in series or parallel describing elastic and viscous behavior. Here, it will be demonstrated that the so-called Generalized Maxwell (GM) model yields comparable results for single pulp fibers at five different RH values and in water. The moisture changes lead to a decrease in the elastic modulus but increase in the relaxation effects with increasing RH. All the determined parameters for the elastic and viscous behavior exhibit a gradual decrease with increasing RH from 10 to 75{\%} RH. The elastic moduli decrease by a factor of 10 and the viscosities are decreasing by a factor of 10–20. In water, there is an even more pronounced decrease of the elastic moduli by a factor 100, and the viscosities decrease by at least three orders of magnitude compared to 10{\%} RH. This indicates that the mechanical response of pulp fibers in water is significantly different than in humid air. This is also illustrated by the fact that a GM model of order two suffices to describe the material behavior in humid air but a GM model of order three is necessary to fit the material behavior in water. A possible interpretation is an additional relaxation effect of the pulp fiber wall in water.",
author = "Czibula, {Caterina Marina} and Christian Ganser and Tristan Seidlhofer and Christian Teichert and Ulrich Hirn",
year = "2019",
doi = "10.1007/s10853-019-03707-1",
language = "English",
journal = "Journal of Materials Science",
issn = "0022-2461",
publisher = "Springer Netherlands",

}

TY - GEN

T1 - Transverse viscoelastic properties of pulp fibers investigated with an atomic force microscopy method

AU - Czibula, Caterina Marina

AU - Ganser, Christian

AU - Seidlhofer, Tristan

AU - Teichert , Christian

AU - Hirn, Ulrich

PY - 2019

Y1 - 2019

N2 - Changes in moisture content of single pulp fibers have an immense influence on the behavior of paper and paper products. Here, an atomic force microscopy (AFM)-based method is applied to investigate the viscoelastic properties of pulp fibers at varying relative humidity (RH) in the transverse direction. Pulp fibers have not only anisotropic properties, but also a very rough surface due to their hierarchical structure. For this reason, we have developed a specific load schedule for the AFM-based test method to overcome uncertainties and limitations due to surface roughness of the pulp fibers. The evaluation of the experimental data combines contact mechanics and viscoelastic models which consist of springs and dashpots in series or parallel describing elastic and viscous behavior. Here, it will be demonstrated that the so-called Generalized Maxwell (GM) model yields comparable results for single pulp fibers at five different RH values and in water. The moisture changes lead to a decrease in the elastic modulus but increase in the relaxation effects with increasing RH. All the determined parameters for the elastic and viscous behavior exhibit a gradual decrease with increasing RH from 10 to 75% RH. The elastic moduli decrease by a factor of 10 and the viscosities are decreasing by a factor of 10–20. In water, there is an even more pronounced decrease of the elastic moduli by a factor 100, and the viscosities decrease by at least three orders of magnitude compared to 10% RH. This indicates that the mechanical response of pulp fibers in water is significantly different than in humid air. This is also illustrated by the fact that a GM model of order two suffices to describe the material behavior in humid air but a GM model of order three is necessary to fit the material behavior in water. A possible interpretation is an additional relaxation effect of the pulp fiber wall in water.

AB - Changes in moisture content of single pulp fibers have an immense influence on the behavior of paper and paper products. Here, an atomic force microscopy (AFM)-based method is applied to investigate the viscoelastic properties of pulp fibers at varying relative humidity (RH) in the transverse direction. Pulp fibers have not only anisotropic properties, but also a very rough surface due to their hierarchical structure. For this reason, we have developed a specific load schedule for the AFM-based test method to overcome uncertainties and limitations due to surface roughness of the pulp fibers. The evaluation of the experimental data combines contact mechanics and viscoelastic models which consist of springs and dashpots in series or parallel describing elastic and viscous behavior. Here, it will be demonstrated that the so-called Generalized Maxwell (GM) model yields comparable results for single pulp fibers at five different RH values and in water. The moisture changes lead to a decrease in the elastic modulus but increase in the relaxation effects with increasing RH. All the determined parameters for the elastic and viscous behavior exhibit a gradual decrease with increasing RH from 10 to 75% RH. The elastic moduli decrease by a factor of 10 and the viscosities are decreasing by a factor of 10–20. In water, there is an even more pronounced decrease of the elastic moduli by a factor 100, and the viscosities decrease by at least three orders of magnitude compared to 10% RH. This indicates that the mechanical response of pulp fibers in water is significantly different than in humid air. This is also illustrated by the fact that a GM model of order two suffices to describe the material behavior in humid air but a GM model of order three is necessary to fit the material behavior in water. A possible interpretation is an additional relaxation effect of the pulp fiber wall in water.

UR - http://www.scopus.com/inward/record.url?scp=85066484954&partnerID=8YFLogxK

U2 - 10.1007/s10853-019-03707-1

DO - 10.1007/s10853-019-03707-1

M3 - Article

JO - Journal of Materials Science

T2 - Journal of Materials Science

JF - Journal of Materials Science

SN - 0022-2461

ER -